Custom Parts Store

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 23-036 JIMS BREATHER REAMER TOOL FOR 19361999 BIG TWIN Tool will repair a damaged breather hole in 1936 thru 1999 single cam Big Twin motors to use a .030" oversize breather gear (ZPN 760559 or ZPN 760561) without disassembly of the crankcase in less than an hour time. 756304 Complete Jims reamer tool kit for 1936-1999 756305 Replacement reamer only JIMS BALANCER INNER BEARING REMOVER/INSTALLER FOR TWIN CAM B This Jims tool will accurately, and safely install or remove the inner balancer bearing mounted in the left engine case. This tool is designed for use on both early and late Twin Cam B crankcases and can all be done on a work bench without using an arbor press. Comes complete with instruction sheet. 751085 Jims Twin Cam B blancer inner bearing remover & installer tool 756306 Installer tool precisely mounts the balancer bearings in the proper location via case bolt and dowel locations without using a driver or press 756309 Tool to remove the balancer bearings without damage to the crankcase JIMS BALANCER BEARING TOOLS FOR MILWAUKEE EIGHT The Milwaukee Eight engine in 2017 to present Touring & Trike and 2018 to present Softail incorporates balancers to reduce vibrations. Incorrect installation of the balancer bearings can cause severe damage to the crankcase or even complete engine failure. JIMS BALANCER SHAFT BEARING REMOVER AND INSTALLER This tool will pull the bearing from the Twin Cam "B" motor case in one easy smooth motion preventing any damage to the bearing bores. The installing portion of this tool is designed to push on the outer diameter of bearing preventing any damage to the bearing itself or it's bore. 750313 Balancer shaft and bearing remover and installer tool. JIMS TWIN CAM "B" BALANCER SHAFT ALIGNMENT TOOL This tool is a must have for maintaining a long life of your balancer drive chains and bearings. When using this tool there is no need for guessing for alignment because it will take all the guess work out of setting up your sprocket and chain alignment on a Twin Cam "B" engine. 750312 Jim's balancer shaft alignment tool JIMS CASE BORING TOOL An easy to use tool that allow you to bore 2006 Dyna Twin Cam and all 2007 thru 2017 Twin Cam crankcases on a heavy-duty 16" drill press to accept up-to 4 1/8" bore cylinders. 750701 Twin Cam case boring tool JIMS CASE SPLITTER TOOL FOR TWIN CAM Use this tool to "break" the case sealant by pushing apart both crankcase halves. You just bolt the tool with the supplied hardware to the primary mounting holes. Thread-in the pushing screw by hand and the case will come part and flywheels will be pushed from the left case. No impact tools needed. Works on 2006 Dyna Twin Cam and all Twin Cam 2007 thru 2017. 750698 Jims crankcase splitter tool JIMS CRANK SHAFT BUSHING TOOL FOR TWIN CAM This Jims tool will remove and install crankshaft bushings in the support plate on Twin Cam models. Piloted for accurate operation. 720492 Crank shaft bushing tool MILWAUKEE EIGHT BALANCER SCISSOR GEAR TOOL Used to hold the two halves of the spring loaded balancer gear in alignment before removal for easy installation. Brightly colored to remind you that you have to remove it before sealing the engine case. 753685 Works on 2017 to present Milwaukee Eight engines in Touring and Trike models JIMS BALANCER SHAFT RETENTION PINS FOR TWIN CAM "B" This tool is developed to secure the engine balancers on Twin Cam "B" engines when servicing the flywheel assembly This tool locks into the balancer's sprocket pin holes to prevent the balancer from turning out of synchronization with the flywheel. 750311 Jims balancer shaft retention pins O�L� C�E�I�A�S & T�O�S LOWER END TOOLS