Custom Parts Store

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 23-034 TIMKEN BEARING REMOVER This tool will remove the sprocket shaft Timken bearing on 1986 thru 1999 Big Twin and 1999 thru 2002 Twin Cam. A specialized tool that does the job better than anything else on the market. 233478 Sprocket shaft bearing remover JIMS SNAP RING INSTALLER & REMOVER TOOL Exclusively designed by Jims to make installation and removal of Timken outer race snap rings easy and without damaging the case. A must when working on 1990 to present cases without inserts. This tool can be used on all Big Twin models from 1969 to present and comes with instructions. 233154 Snap ring installer & remover tool 233199 Sprocket shaft seal install tool 235810 Basic sprocket shaft bearing installing tool 753619 Upgrade kit to use ZPN 235810 on 2006 thru 2017 Dyna, 2007 thru 2017 Softail and 2007 thru 2016 Touring 235848 Main shaft sprocket locknut wrench (OEM 94660-37A) JIMS SPROCKET SHAFT BEARING & SEAL INSTALLING TOOLS Designed to give the best control on the torque of bearing pack for checking bearing end play. Torque nut with JIMS tool ZPN 235848 for consistent professional results. The basic sprocket shaft tool works on all Big Twin engines from 1955 thru 1999 and 1999 thru 2005 Twin Cam. To use this tool on 2006 thru 2017 Twin Cams you will also need the ZPN 753619 upgrade kit. Use with ZPN 233199 to install the sprocket shaft oil seal. LEFT CRANKCASE BEARING RACE INSTALLER Use to install the bearing race in the left crankcase. With this tool you can press in the bearing races straight time after time. Use on Big Twins from 1969 thru 2002 and Sportster models from 1977 thru 2003. 239480 Left crankcase bearing race installer TIMKEN BEARING REMOVER FOR BIG TWIN This tool will remove the sprocket shaft Timken bearing on Big Twin models with a separate sprocket shaft as stock from 1955 thru 1985 and as found in aftermarket flywheels for models from 1955 to present. 235793 Sprocket shaft bearing remover TIMKEN BEARING REMOVER FOR SPORTSTER MODELS This tool is used to remove the Timken bearing from the sprocket shaft without removing the shaft from the flywheels. Can be used on all Sportster models from 1977 thru 2003 and Buell models from 1987 thru 2003. 233470 Bearing remover SPROCKET SHAFT BEARING PULLER FOR SPORTSTER With this tool you can easily remove the inner Timken bearing from the sprocket shaft without removing the shaft from the flywheels. Use on Sportster engines from 1957 thru 1976. 239479 Sprocket shaft bearing puller JIMS SPROCKET SHAFT BEARING AND RACE PULLER TOOL This tool has been designed to remove the flywheel sprocket shaft inner bearing race on all 1955 thru 1999 Big Twin and 1999 thru 2017 Twin Cam. Comes complete with JIMS T-bar and hardware. If heat is needed to remove race see tool ZPN 751111 surface temperature indicator strips. • Also removes pinion shaft inner bearing race on 1954 to present Sportster and air cooled Buell's • Also to remove press fit transmission gears and bearings from input and output shafts on all V-Rod models 2002 thru 2017 753617 Jims bearing and race puller tool JIMS SPORTSTER SPROCKET SHAFT SEAL INSTALLER Installs the sprocket shaft seal on 1995-2003 Sportster and 1995-2002 Buell perfectly square and at the proper depth. Use in conjunction with ZPN 753605 installer tool. 753658 Sprocket shaft seal installer tool 753605 Main seal installer tool JIMS CRANKSHAFT BEARING INSTALLER AND REMOVER FOR TWIN CAM "B" MODELS Designed to protect expensive engine cases by using a specially designed support block to remove or install cam side crankshaft bearing on Twin Cam models with balance shafts (TC88B). Use Zodiac press fit lube ZP N741905 on case and bearings while installing. 741905 Crankshaft bearing installer & remover O�L� C�E�I�A�S & T�O�S LOWER END TOOLS